Troubleshooting Incomplete Laser Cuts
Compare the job preview with the physical cut before changing power or speed. Missing paths or intentional holding tabs require different checks from a complete path that does not cut through. Inspect geometry and operation assignments first, then material, focus and machine condition. Additional passes are not proof that a job is within the machine’s documented capability.
Published by: Laserlinez
Find the stage that needs attention
| Observation | First check |
|---|---|
| Paths missing in the preview | Check geometry, assigned operation and enabled output. |
| Gaps deliberately shown in a line | Check whether Tabs / Bridges or Perforation Mode are intended. |
| Complete preview, incomplete physical cut | Check material, focus, machine condition and the selected cutting setup. |
Compare the planned path with the result
Inspect the job preview before running another cut. Are sections missing from the planned cutting path, or does the software show a complete path that the machine failed to cut through? The preview helps separate file and operation problems from questions about cutting performance. It cannot predict whether your material will be cut through.
In LightBurn, Tabs / Bridges and Perforation Mode deliberately skip sections of a line. Check whether those gaps are intended before removing them. If the preview is complete but the physical cut is not, check the material and machine setup as well as the selected cutting settings.
Check the geometry and assigned operation
An open path is not automatically an error: LightBurn can follow it in Line mode. If you intend to cut out a separate part, inspect its entire boundary for unintended gaps. Do not close intentional open lines, and do not assume small gaps will be joined automatically.
Select the intended operation in the receiving software and check that its output is enabled. In LightBurn, Line mode follows vector paths; whether it marks the surface or cuts through depends on the job settings and the machine/material combination. An SVG fill, a thin stroke or a group named CUT does not by itself configure a through-cut.
Check for accidental duplicate paths and repeated operations. They can cause the same area to be processed again. Use the editor's geometry tools and the job preview; overlapping paths can look like a single line. Preserve intentional repeated passes and keep an unchanged copy before cleaning the file.
Check material, focus and machine condition
Identify the material, measure its actual thickness and confirm that your machine is suitable for cutting it. A setting for one laser or material is not a universal recipe. Use the manufacturer's guidance for your exact setup; do not process unidentified material.
Set focus using the procedure specified for your machine and job. There is no universal focus-gauge distance. Check that the workpiece is supported as instructed: warping can change its distance from the head, and variations in thickness or composition can change the result.
Follow the machine's instructions for checking optics, air assist where fitted, and extraction. Before inspecting or cleaning components, follow its shutdown and maintenance procedure. Do not compensate for damaged or dirty optics by repeatedly increasing power; use the specified cleaning method or contact support.
Run a controlled test
Establish a suitable starting point
Use documented cutting settings for your machine and material. Confirm the speed units (mm/s or mm/min), power and pass count. If compatibility or a suitable starting point is unclear, consult the manufacturer before testing.
Use representative material
Choose a spare piece of the intended material with matching thickness and surface finish, preferably from the same batch. Use a simple test shape and the same support and focus procedure as for the job.
Observe the test
Use the machine's required safeguards and extraction, and stay with it throughout the cut. Stop for fire or malfunction and follow the manufacturer's emergency procedure.
Change one factor at a time
After the machine is safe to access, inspect the result. If an adjustment is appropriate, change one setting within the manufacturer's guidance and compare another sample. A shallow cut or a charred edge alone does not prove which setting is wrong.
Confirm the actual job
Check a representative part before committing the full sheet. Record the material, measured thickness, focus procedure, settings with units, file version and result. A successful simple test does not guarantee every feature of a larger design will cut correctly.
When another pass is not the answer
Additional passes can be appropriate for supported jobs, but they do not establish that a material or thickness beyond the machine's documented capability is suitable. Do not rely on a fixed percentage increase in power, a fixed speed reduction or a promised extra thickness.
If a previously reliable job starts failing, investigate what changed. If it still fails after the documented checks, stop repeating cuts and contact the manufacturer. Provide the machine model, material and thickness, file, settings and photos of the result.
When file conversion can help
If the intended cutting boundary exists only as pixels, Laserlinez Contour Vectorization can create vector boundaries to inspect and assign to a cutting operation. It does not diagnose focus, restore laser output or determine settings for your material. If the preview already contains the correct paths, investigate the cutting process rather than repeating the conversion.
Common questions
Compare actual thickness, material batch, surface finish, flatness, support and focus. Then compare the project preview with the test: operations, gaps and repeated paths may differ. The difference is a clue to investigate, not proof that the file or power setting alone is responsible.
First check compatibility, the planned operation, focus and machine condition. Either setting may be relevant, but neither has a universal adjustment amount or guarantees a cleaner cut. Use the manufacturer's guidance and change one factor at a time on a suitable sample.
Vectorization can help when you need contours from a bitmap. It cannot repair the machine or determine suitable cutting settings. If you already have the required paths, inspect their geometry and assigned operations before converting anything again.
Before cutting the final parts
- Material and thickness are identified and suitable for the machine.
- Size, units, intended boundaries and operations are correct in the receiving software.
- The preview contains the intended cuts, with no accidental gaps or repetitions.
- Focus, support, machine condition and required safeguards have been checked.
- A representative test meets the job's requirements and its settings are recorded.
Comments
Loading comments...